Saltar al contenido




  • 【Support 4S Power】The greatest combination of F4 V2 FC with BLHeli_32 16A ESC built-in BetaFlight OSD is customized for Cine whoop drone Beta85X. Which totally supports 4S POWER with a steady performance
  • 【BLHeli_32 16A ESC】BLHeli_32 is the 3rd generation ESC firmware after BLHeli and BLHeli_S, which is written for ESC’s that utilize 32-bit MCU. With the increase in processing power, faster input signals with lower latency and higher update rate would be possible in BLHeli_32, such as Dshot1200
  • 【Updated of F4 V2 FC】F4 V2 FC upgraded the connection mode with accessories, added 4 extra pluggable ports for ESC, RX, VTX and led board, no need to solder, which is convenient for installation and decreasing the dislocated PIN mounting
  • 【Upgraded of ESC】Using single N-channel MosFETs on ESC board, which has a lower inner resistance. It is dual MosFETs on the original BLHeli_32 ESC board. Current sensor included. Power cable increases electrolytic capacitance, reducing the high voltage damage to the electronic components during the power-on, and functions as a circuit protection
  • 【Please note】The F4 V2 FC BLHeli_32 16A ESC is without receiver, all the ports are available on this board. The details of soldering receiver please refer to the pictures on the left. When you connect the receiver to this F4 V2 FC, don’t forget to plug the battery, otherwise the receiver will have no power to work at all

Descripción del producto

BETAFPV Upgraded F4 V2 FC 4S Brushless Flight Controller and BLHeli_32 16A ESC OSD Smart Audio No Receiver with XT30 Cable for Brushless FPV Micro Drone Cine Whoop Beta85X

F4 V2 FC
CPU: STM32F405 (Overclock to 240MHz)
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
RX3 and TX3 are with auto inverter, supporting all RX including TBS Micro RX
TX01 and RX01 ports are available for Frsky F-Port, DSM2/DSMX
Buzzer solder pads
Support programable LED like WS2812 etc
Weight: 4.2g

BLHeli_32 16A ESC
Support BLHELI_32
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200
Input voltage: 3-4S lipo
Cotinue current: 16A
Peak current: 19A
Firmware target: BETAFPV-16A-32bit
MCU: STM32F051K66
Motor Connectors: 1.25mm header pins connector
Weight: 4.4g (7.7g with XT30 cable)

Recommend Parts
Beta85X 4S Frame Kit:
1105 5000KV Motors:
BETAFPV 450mAh 4S Battery:

1 * F4 V2 FC BLHeli_32 16A ESC
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
1 * 3-Pin Led Board Cable
1 * 4-Pin Receiver Cable
1 * 7-Pin 4S 16A ESC Cable






No hay valoraciones aún.

Sé el primero en valorar “MICRO CONTROLADORA FC BETAFPV Upgraded F4 V2 4S”

Tu dirección de correo electrónico no será publicada. Los campos obligatorios están marcados con *